69 lines
2.1 KiB
Arduino
69 lines
2.1 KiB
Arduino
|
/**
|
||
|
|
* @file audio-out.ino
|
||
|
|
* @brief Sine wave playback for the Guition JC4880P443C_I_W (ESP32-P4)
|
||
|
|
* onboard ES8311 codec + NS4150 speaker amp, via I2SCodecStream.
|
||
|
|
*
|
||
|
|
* There's no arduino-audio-driver board entry for this board, so this
|
||
|
|
* uses arduino-audio-driver's `GenericES8311` (no predefined pins - the
|
||
|
|
* same pattern the wiki documents for `GenericWM8960`/ES8388: `Wire`
|
||
|
|
* is set up manually for codec I2C, and I2S pins are set directly on
|
||
|
|
* the stream config).
|
||
|
|
*
|
||
|
|
* `GenericES8311` has no `PinFunction::PA` pin, so unlike a
|
||
|
|
* board-specific entry it does not toggle the NS4150 amp-enable pin for
|
||
|
|
* you - this file does that manually. PA_EN (GPIO11) is driven
|
||
|
|
* active-HIGH, confirmed on real hardware.
|
||
|
|
*
|
||
|
|
* Dependencies:
|
||
|
|
* - https://github.com/pschatzmann/arduino-audio-tools
|
||
|
|
* - https://github.com/pschatzmann/arduino-audio-driver
|
||
|
|
* @author Phil Schatzmann
|
||
|
|
* @copyright GPLv3
|
||
|
|
*/
|
||
|
|
|
||
|
|
#include "AudioTools.h"
|
||
|
|
#include "AudioTools/AudioLibs/I2SCodecStream.h"
|
||
|
|
|
||
|
|
// Pins from guition-jc4880p4-bsp's board_p4_pins.h "Audio" section.
|
||
|
|
constexpr int kPinI2sMclk = 13;
|
||
|
|
constexpr int kPinI2sBck = 12;
|
||
|
|
constexpr int kPinI2sWs = 10;
|
||
|
|
constexpr int kPinI2sDout = 9; // P4 -> codec
|
||
|
|
constexpr int kPinCodecScl = 8; // shared with GT911 touch bus
|
||
|
|
constexpr int kPinCodecSda = 7;
|
||
|
|
constexpr int kPinAmpEnable = 11; // NS4150 PA_EN, active-high
|
||
|
|
|
||
|
|
AudioInfo info(44100, 2, 16);
|
||
|
|
SineWaveGenerator<int16_t> sineWave;
|
||
|
|
GeneratedSoundStream<int16_t> sound(sineWave);
|
||
|
|
I2SCodecStream out(GenericES8311);
|
||
|
|
StreamCopy copier(out, sound);
|
||
|
|
|
||
|
|
void setup(void) {
|
||
|
|
Serial.begin(115200);
|
||
|
|
AudioToolsLogger.begin(Serial, AudioToolsLogLevel::Warning);
|
||
|
|
|
||
|
|
pinMode(kPinAmpEnable, OUTPUT);
|
||
|
|
digitalWrite(kPinAmpEnable, HIGH); // enable NS4150
|
||
|
|
|
||
|
|
Wire.begin(kPinCodecSda, kPinCodecScl);
|
||
|
|
|
||
|
|
Serial.println("starting I2S...");
|
||
|
|
auto config = out.defaultConfig(TX_MODE);
|
||
|
|
config.copyFrom(info);
|
||
|
|
config.pin_mck = kPinI2sMclk;
|
||
|
|
config.pin_bck = kPinI2sBck;
|
||
|
|
config.pin_ws = kPinI2sWs;
|
||
|
|
config.pin_data = kPinI2sDout;
|
||
|
|
if (!out.begin(config)) {
|
||
|
|
Serial.println("error!");
|
||
|
|
stop();
|
||
|
|
}
|
||
|
|
out.setVolume(0.5f);
|
||
|
|
|
||
|
|
sineWave.begin(info, N_B4);
|
||
|
|
Serial.println("started...");
|
||
|
|
}
|
||
|
|
|
||
|
|
void loop() { copier.copy(); }
|