58 lines
1.8 KiB
Arduino
58 lines
1.8 KiB
Arduino
|
/**
|
||
|
|
* @file audio-in.ino
|
||
|
|
* @brief Microphone test for the Guition JC4880P443C_I_W (ESP32-P4):
|
||
|
|
* reads the ES8311 codec's ADC path and prints PCM samples to Serial as
|
||
|
|
* CSV - open the Arduino IDE's Serial Plotter to see the waveform, or
|
||
|
|
* just watch for non-zero values while talking near the board.
|
||
|
|
*
|
||
|
|
* Uses arduino-audio-driver's `GenericES8311` (no predefined pins) - see
|
||
|
|
* audio-out.ino for why, and for this board's I2S/I2C pins.
|
||
|
|
*
|
||
|
|
* Dependencies:
|
||
|
|
* - https://github.com/pschatzmann/arduino-audio-tools
|
||
|
|
* - https://github.com/pschatzmann/arduino-audio-driver
|
||
|
|
* @author Phil Schatzmann
|
||
|
|
* @copyright GPLv3
|
||
|
|
*/
|
||
|
|
|
||
|
|
#include "AudioTools.h"
|
||
|
|
#include "AudioTools/AudioLibs/I2SCodecStream.h"
|
||
|
|
|
||
|
|
// Pins from guition-jc4880p4-bsp's board_p4_pins.h "Audio" section.
|
||
|
|
constexpr int kPinI2sMclk = 13;
|
||
|
|
constexpr int kPinI2sBck = 12;
|
||
|
|
constexpr int kPinI2sWs = 10;
|
||
|
|
constexpr int kPinI2sDin = 48; // codec -> P4, the mic-in path this file reads
|
||
|
|
constexpr int kPinCodecScl = 8; // shared with GT911 touch bus
|
||
|
|
constexpr int kPinCodecSda = 7;
|
||
|
|
|
||
|
|
AudioInfo info(16000, 2, 16);
|
||
|
|
I2SCodecStream in(GenericES8311);
|
||
|
|
CsvOutput<int16_t> csvOutput(Serial);
|
||
|
|
StreamCopy copier(csvOutput, in); // copies mic data to Serial as CSV
|
||
|
|
|
||
|
|
void setup(void) {
|
||
|
|
Serial.begin(115200);
|
||
|
|
AudioToolsLogger.begin(Serial, AudioToolsLogLevel::Info);
|
||
|
|
AudioDriverLogger.begin(Serial, AudioDriverLogLevel::Info);
|
||
|
|
|
||
|
|
Wire.begin(kPinCodecSda, kPinCodecScl);
|
||
|
|
|
||
|
|
Serial.println("starting I2S...");
|
||
|
|
auto config = in.defaultConfig(RX_MODE);
|
||
|
|
config.copyFrom(info);
|
||
|
|
config.pin_mck = kPinI2sMclk;
|
||
|
|
config.pin_bck = kPinI2sBck;
|
||
|
|
config.pin_ws = kPinI2sWs;
|
||
|
|
config.pin_data = kPinI2sDin; // RX pin in RX_MODE
|
||
|
|
if (!in.begin(config)) {
|
||
|
|
Serial.println("error!");
|
||
|
|
stop();
|
||
|
|
}
|
||
|
|
|
||
|
|
csvOutput.begin(info);
|
||
|
|
Serial.println("started...");
|
||
|
|
}
|
||
|
|
|
||
|
|
void loop() { copier.copy(); }
|